Thousandth of an inch
A thousandth of an inch is a derived unit of length in a system of units using inches. Equal to 1⁄1000 of an inch, a thousandth is commonly called a thou // (used for both singular and plural) or particularly in North America a mil (plural mils).
|Thousandth of an inch|
|Symbol||thou or mil|
|1 thou in ...||... is equal to ...|
|imperial and US customary systems||0.001 in|
|SI units||25.4 μm|
The words are shortened forms of the English and Latin words for "thousand" (mille in Latin). In international engineering contexts, confusion can arise because mil is a formal unit name in North America but mil or mill is also a common colloquial clipped form of millimetre. The units are considerably different: a millimetre is approximately 39 mils.
Contexts of use
- The thickness of items such as paper, film, foil, wires, paint coatings, latex gloves, plastic sheeting, and fibers
- Manufacturing dimensions and tolerances, such as:
- In the manufacture of older automobile engines (A typical example is the thickness of the head gasket, or the amount of material to be removed from the head to adjust the compression ratio of the cylinders.)
- In the servicing of older automobile engines (typical examples include a spark-plug gap or ignition points gap.)
- The manufacture of printed circuit boards (PCBs) (although the component dimensions are now typically provided in millimetres, because they are sold worldwide)
- Tolerance specifications on hydraulic cylinders
There are also compound units such as "mils per year" used to express corrosion rates.
In machining, where the thou is often treated as a basic unit, 0.0001 inches (2.54 micrometres) can be referred to as "one tenth", meaning "one tenth of a thou" or "one ten thousandth". (The metric comparison is discussed below.) Machining "to within a few tenths" is often considered very accurate, and at or near the extreme limit of tolerance capability in most contexts. Greater accuracy (tolerance ranges inside one tenth) apply in only a few contexts: in plug gauge and gauge block manufacturing or calibration, they are typically expressed in millionths of an inch or, alternatively, in micrometres; in nanotechnology, nanometres or picometres are used.
Usage notes on mil versus thou
In the United States, mil was once the more common term, but as use of the metric system has become more common, thou has replaced mil among most technical users to avoid confusion with millimetres. Today both terms are used, but in specific contexts one is traditionally preferred over the other.
Equivalence to other units of length
1 thou is equal to:
History of usage
- ...instead of our engineers and machinists thinking in eighths, sixteenths and thirty-seconds of an inch, it is desirable that they should think and speak in tenths, hundredths, and thousandths...
Whitworth's main point was to advocate decimalization in place of fractions based on successive halving; but in mentioning thousandths, he was also broaching the idea of a finer division than had been used previously. Up until this era, workers such as millwrights, boilermakers, and machinists measured only in traditional fractions of an inch, divided via successive halving, usually only as far as 64ths (1, 1⁄2, 1⁄4, 1⁄8, 1⁄16, 1⁄32, 1⁄64). Each 64th is about 16 thou. Communication about sizes smaller than a 64th of an inch was subjective and hampered by a degree of ineffability—while phrases such as "scant 64th" or "heavy 64th" were used, their communicative ability was limited by subjectivity. Dimensions and geometry could be controlled to high accuracy, but this was done by comparative methods: comparison against templates or other gauges, feeling the degree of drag of calipers, or simply repeatably cutting, relying on the positioning consistency of jigs, fixtures, and machine slides. Such work could only be done in craft fashion: on-site, by feel, rather than at a distance working from drawings and written notes. Although measurement was certainly a part of the daily routine, the highest-precision aspects of the work were achieved by feel or by gauge, not by measuring (as in determining counts of units). This in turn limited the kinds of process designs that could work, because they limited the degree of separation of concerns that could occur.
The introduction of thou as a base unit for machining work required the dissemination of vernier calipers and screw micrometers throughout the trade, as the unit is too small to be measured with practical repeatability using rules alone. (Most rule markings were far too wide to mark a single mil, and even if such dividing is accomplished, it is illegible to the naked eye, being discernible but not useful for measuring.) During the following half century, such measuring instruments went from expensive rarities to widespread, everyday tools among machinists. Bringing more metrology into machining increased the separation of concerns to make possible, for example, designing an assembly to the point of an engineering drawing, then having the mating parts made at different firms who did not have any contact with (or even awareness of) each other—yet still knowing with certainty that their products would have the desired fit.
- ^ "mil" . Lexico UK Dictionary. Oxford University Press.
- ^ "Paper weight comparison and more" . paper-paper.com. Micro Format. Retrieved 2016-01-18.
- ^ "Guitar Strings" . FaChords Guitar. July 2020. Retrieved 2020-07-31.
- ^ "The Gerber Format Specification" (PDF). Ucamco. July 2014. p. 30. Retrieved 2014-08-27.
- ^ Skinner, Richard D., ed. (1993). "Packaging". Basic Integrated Circuit Technology Reference Manual (PDF). US: Integrated Circuit Engineering Corporation. ISBN 1-877750-24-7. Retrieved 2021-07-10 – via Smithsonian Chips.
- ^ "Corrosion Rate Conversion" , Corrosionist.com
- ^ "...the smallest move of one-tenth (not 0.1 but 0.0001 of an inch)..." , Dan Nelson, The CNC Toolbox, p89
- ^ a b Mil at How Many? A Dictionary of Units of Measurement by Russ Rowlett
- ^ a b University of Queensland: PCB design FAQ
- ^ Thou at How Many? A Dictionary of Units of Measurement by Russ Rowlett
- ^ Edkins, Jo. "Small units" . Imperial Measures of Length. Jo Edkins. Retrieved 2009-09-23.
- ^ "A Paper on Standard Decimal Measures of Length", Manchester, 1857
Information as of: 16.08.2021 11:32:26 CEST
Source: Wikipedia (Authors [History]) License of the text: CC-BY-SA-3.0. Creators and licenses of the individual images and media can either be found in the caption or can be displayed by clicking on the image.
Changes: Design elements were rewritten. Wikipedia specific links (like "Redlink", "Edit-Links"), maps, niavgation boxes were removed. Also some templates. Icons have been replaced by other icons or removed. External links have received an additional icon.
Please note: Because the given content is automatically taken from Wikipedia at the given point of time, a manual verification was and is not possible. Therefore WikiFox.org does not guarantee the accuracy and actuality of the acquired content. If there is an Information which is wrong at the moment or has an inaccurate display please feel free to contact us: email.